This HTML5 document contains 57 embedded RDF statements represented using HTML+Microdata notation.

The embedded RDF content will be recognized by any processor of HTML5 Microdata.

Subject Item

dbr:Differential_TTL

rdf:type

yago:Organization108008335 yago:Abstraction100002137 yago:Family108078020 yago:Group100031264 yago:WikicatLogicFamilies yago:Unit108189659 yago:YagoLegalActorGeo yago:YagoPermanentlyLocatedEntity yago:SocialGroup107950920 yago:YagoLegalActor

rdfs:label

Differential TTL

rdfs:comment

Differential TTL is a type of binary electrical signaling based on the transistor-transistor logic (TTL) concept. Standards implementing differential TTL include RS-422. It enables electronic systems to be relatively immune to noise. Differential TTL is the most common type of high-voltage differential signaling (HVDS).

owl:sameAs

n14:03kj0y n15:f83E yago-res:Differential_TTL wd:Q17010586 dbpedia-fa:تی‌تی‌ال_تفاضلی dbr:Differential_TTL

foaf:topic

dbr:Serial_Storage_Architecture dbr:RS-422 dbr:Differential_signalling n20:this dbr:TTL dbr:Transistor–transistor_logic wikipedia-en:Differential_TTL

wdrs:describedby

n12:Differential_signaling n12:Type n23:Family108078020 n26:Differential_signaling n27:Family108078020

dct:subject

dbc:Logic_families

dbo:wikiPageID

873133

dbo:wikiPageRevisionID

1118461140

dbo:wikiPageWikiLink

dbr:Electric_current dbr:RS-422 n7: dbr:HVDS dbr:Single-ended_signaling dbc:Logic_families dbr:Electronics dbr:LVDS dbr:Differential_signaling dbr:Serial_Storage_Architecture n24: dbr:High-voltage_differential_signaling dbr:Differential_signalling dbr:Transistor-transistor_logic dbr:Electromagnetic_field dbr:Low-voltage_differential_signaling dbr:Logic_level

foaf:isPrimaryTopicOf

wikipedia-en:Differential_TTL

prov:wasDerivedFrom

n9:0

n28:hypernym

dbr:Type

dbo:abstract

Differential TTL is a type of binary electrical signaling based on the transistor-transistor logic (TTL) concept. Standards implementing differential TTL include RS-422. It enables electronic systems to be relatively immune to noise. Normal TTL signals are single-ended, which means that each signal consists of a voltage on one wire, referenced to a system ground. The "low" voltage level is zero to 0.8 volts, and the "high" voltage level is 2 volts to 5 volts. A differential TTL signal consists of two such wires, also referenced to a system ground. The logic level on one wire is always the complement of the other. The principle is similar to that of low-voltage differential signaling (LVDS), but with different voltage levels. Differential TTL is used in preference to single-ended TTL for long-distance signaling. In a long cable, stray electromagnetic fields in the environment, or stray currents in the system ground, can induce unwanted voltages that cause errors at the receiver. With a differential pair of wires, roughly the same unwanted voltage is induced in each wire. The receiver subtracts the voltages on the two wires, so that the unwanted voltage disappears, and only the voltage created by the driver remains. A second advantage of differential TTL is that the differential pair of wires can form a current loop. The driver sources a current from the power supply into one wire. This current passes along the wire to the receiver, through the termination resistor and back up the other wire, then back through the driver and down to ground. No net current is exchanged between the driver and receiver, which means that none of the signal current has to return through the ground connection (if there is one) between the two ends. This arrangement prevents the signal from injecting currents into the ground connection, which might upset other circuits attached to it. Differential TTL is the most common type of high-voltage differential signaling (HVDS).

dbo:wikiPageLength

3745

dbp:wikiPageUsesTemplate

dbt:Reflist dbt:Citation_needed